Key Features
• Operating Voltage: 120VDC – 750VDC
• Nominal Charge / Discharge Current: 100A
• Maximum Charge / Discharge Current: 125A
• DC Input Rating: 12VDC / 4.15A
• Operating Temperature Range: -20°C to 55°C
• Ingress Protection: IP20

Protect your system from lightning strikes with the Midnite Solar Surge Protective Device (SPD). Designed for both AC and DC solar electric systems, it provides protection to service panels, load centers, or where the surge protector is directly connected.

Designed for both indoor and outdoor use, the SPD is offered in three different voltages—115, 300 and 600 volts. Protection is achieved by reducing the clamping voltage to a safe level that your system can sustain and that won’t damage electronic components.

This Midnite Solar surge suppressor is a welcome replacement to arrestors that have been used in the past. Providing eight times the protection as previous arrestors, it is much better at clamping surges to a safe voltage.

Features & Attributes:

• Dimensions (LxWxH): 4.4 × 3.8 × 3.5 inches
• Weight: 0.4 kg
• Much safer than previous surge suppressors
• Engineered for both AC and DC electric systems
• ETL listed
• Type 1 Device
• MPN: MNSPD-300-AC

RSI 3×380-440V IP66 15kW 31A

Renewable Solar Inverter RSI is an off-grid solar inverter to enable end-user to use solar power for a wide range of water applications. RSI is customized specifically to be compatible with Grundfos pumps. With the built-in MPPT and various protection software, it delivers an efficient and reliable solar system solution.

RSI offers the following inputs and output:

• Solar charge controller

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges a battery bank.

The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.

• MPPT: Ultra Fast Maximum Power Point Tracking

The MPPT VE.Can SmartSolar charger connects to a PV array of 150 or 250 Volt Voc and will automatically detect and charge your 12, 24, or 48V battery bank with current ranging from 70 to 100A depending on the model.

The charge settings are fully programmable and can even be set up for different battery chemistries, like lead-acid, lithium and others.

• Control Your Charger Remotely

The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.

• Daisy Chain Additional Units

The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy-chained” to each other with a single RJ45 cable between the individual units.

When connected to each other, all individual VE.Can SmartSolar chargers, will synchronize their charge stages. They can also send their data, via a single cable, to a GX monitoring device.

• Remote Monitoring and Control

If the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s).

For remote installations – even when there is no internet connection nearby – you may be able to monitor your MPPT by connecting the  GlobalLink 520.

• SmartSolar Control Display

The VE.Can SmartSolar charger is also equipped with a VE.Direct port like our other MPPT solar chargers. This port can be for single unit monitoring or for streetlight control. The remote on/off connector can be externally controlled by a third-party device like a lithium battery. An optional plug-in LCD display/control provides live-data, set-up and management, straight from the face of the device.